Difference between revisions of "Route"

From Linuxintro
imported>ThorstenStaerk
imported>ThorstenStaerk
Line 20: Line 20:
  
 
== Adding a network ==
 
== Adding a network ==
To tell your [[Linux]] to send packages for the network 192.168.0.0[[subnet mask|/]]24 to the network device eth3:
+
To tell your Linux to send packages for the network 192.168.0.0[[subnet mask|/]]24 to the network device eth3:
 
  route add -net 192.168.0.0 netmask 255.255.255.0 eth3
 
  route add -net 192.168.0.0 netmask 255.255.255.0 eth3
 
The same with a default gateway of 192.168.0.1:
 
The same with a default gateway of 192.168.0.1:

Revision as of 18:49, 13 September 2012

The command route lets you view and modify your computer's network routing table. You can use it when troubleshooting network problems or when you have more than one network card.

Overview

If you just call route, you get a list of routing rules, like this:

# route
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.0.0     *               255.255.255.0   U     0      0        0 eth1
link-local      *               255.255.0.0     U     0      0        0 eth1
loopback        *               255.0.0.0       U     0      0        0 lo
default         192.168.0.1     0.0.0.0         UG    0      0        0 eth1

The first blue line means: If there is any IP package for an IP address 192.168.0.*, just send it over network device eth1. The second blue line means: Every IP package that has not been handled yet, send over network device eth1 to the default gateway 192.168.0.1.

Adding a rule

Gateway

For a pc with typical network access, to add a gateway issue

route add default gw 192.168.1.1

(where 192.168.1.1 is the address of your gateway)

Adding a network

To tell your Linux to send packages for the network 192.168.0.0/24 to the network device eth3:

route add -net 192.168.0.0 netmask 255.255.255.0 eth3

The same with a default gateway of 192.168.0.1:

route add -net 192.168.0.0 netmask 255.255.255.0 gw 192.168.0.1 eth3

Removing a rule

# route -n
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.0.0     0.0.0.0         255.255.255.0   U     0      0        0 eth0
192.168.0.0     0.0.0.0         255.255.255.0   U     0      0        0 eth1
169.254.0.0     0.0.0.0         255.255.0.0     U     0      0        0 eth1
127.0.0.0       0.0.0.0         255.0.0.0       U     0      0        0 lo
0.0.0.0         192.168.0.1     0.0.0.0         UG    0      0        0 eth1
# route delete -net 192.168.0.0 netmask 255.255.255.0 eth0
# route -n
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.0.0     0.0.0.0         255.255.255.0   U     0      0        0 eth1
169.254.0.0     0.0.0.0         255.255.0.0     U     0      0        0 eth1
127.0.0.0       0.0.0.0         255.0.0.0       U     0      0        0 lo
0.0.0.0         192.168.0.1     0.0.0.0         UG    0      0        0 eth1

See also