Difference between revisions of "Route"
imported>ThorstenStaerk |
imported>ThorstenStaerk |
||
| (2 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
The [[command]] [[route]] lets you view and modify your computer's network routing table. You can use it when troubleshooting network problems or when you have more than one network card. | The [[command]] [[route]] lets you view and modify your computer's network routing table. You can use it when troubleshooting network problems or when you have more than one network card. | ||
| + | = Overview = | ||
If you just call route, you get a list of routing rules, like this: | If you just call route, you get a list of routing rules, like this: | ||
# route | # route | ||
| Line 19: | Line 20: | ||
== Adding a network == | == Adding a network == | ||
| − | To tell your | + | To tell your Linux to send packages for the network 192.168.0.0[[subnet mask|/]]24 to the network device eth3: |
route add -net 192.168.0.0 netmask 255.255.255.0 eth3 | route add -net 192.168.0.0 netmask 255.255.255.0 eth3 | ||
The same with a default gateway of 192.168.0.1: | The same with a default gateway of 192.168.0.1: | ||
| Line 43: | Line 44: | ||
= See also = | = See also = | ||
| − | * [http:// | + | * [http://linux.die.net/man/8/route route man page] |
Latest revision as of 07:59, 6 December 2013
The command route lets you view and modify your computer's network routing table. You can use it when troubleshooting network problems or when you have more than one network card.
Overview
If you just call route, you get a list of routing rules, like this:
# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.0.0 * 255.255.255.0 U 0 0 0 eth1 link-local * 255.255.0.0 U 0 0 0 eth1 loopback * 255.0.0.0 U 0 0 0 lo default 192.168.0.1 0.0.0.0 UG 0 0 0 eth1
The first blue line means: If there is any IP package for an IP address 192.168.0.*, just send it over network device eth1. The second blue line means: Every IP package that has not been handled yet, send over network device eth1 to the default gateway 192.168.0.1.
Adding a rule
Gateway
For a pc with typical network access, to add a gateway issue
route add default gw 192.168.1.1
(where 192.168.1.1 is the address of your gateway)
Adding a network
To tell your Linux to send packages for the network 192.168.0.0/24 to the network device eth3:
route add -net 192.168.0.0 netmask 255.255.255.0 eth3
The same with a default gateway of 192.168.0.1:
route add -net 192.168.0.0 netmask 255.255.255.0 gw 192.168.0.1 eth3
Removing a rule
# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth1 # route delete -net 192.168.0.0 netmask 255.255.255.0 eth0 # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth1
