Difference between revisions of "Ping"
imported>ThorstenStaerk |
|||
| Line 10: | Line 10: | ||
= Broadcast ping = | = Broadcast ping = | ||
| − | + | A broadcast ping can be described as a request "Anybody who hears this, please respond back". The problem is that you can configure computers to ignore these requests. | |
| − | + | ||
| − | + | To tell your computer to ''answer'' on broadcast pings, [[open a console]] and issue: | |
| − | |||
echo "0" >/proc/sys/net/ipv4/icmp_echo_ignore_broadcasts | echo "0" >/proc/sys/net/ipv4/icmp_echo_ignore_broadcasts | ||
| − | + | ||
| + | To verify if your computer is set to answer on broadcast pings, issue: | ||
sysctl net.ipv4.icmp_echo_ignore_broadcasts | sysctl net.ipv4.icmp_echo_ignore_broadcasts | ||
| + | In this case, the response | ||
net.ipv4.icmp_echo_ignore_broadcasts = 0 | net.ipv4.icmp_echo_ignore_broadcasts = 0 | ||
| + | means it is set to answer. | ||
| + | |||
| + | To perform a broadcast ping, | ||
* Find out the broadcast address of the network where you want to broadcast | * Find out the broadcast address of the network where you want to broadcast | ||
ifconfig eth1 | ifconfig eth1 | ||
| Line 29: | Line 33: | ||
RX bytes:195071533 (186.0 Mb) TX bytes:41401952 (39.4 Mb) | RX bytes:195071533 (186.0 Mb) TX bytes:41401952 (39.4 Mb) | ||
Interrupt:21 Base address:0x4000 | Interrupt:21 Base address:0x4000 | ||
| − | * ping | + | * ping the broadcast IP |
# ping -b 192.168.0.255 | # ping -b 192.168.0.255 | ||
WARNING: pinging broadcast address | WARNING: pinging broadcast address | ||
Revision as of 19:51, 13 July 2011
Ping allows you to see if a computer is reachable via the network and to measure the network latency. You stop it with CTRL_C.
Example:
# ping 192.168.0.1 PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data. 64 bytes from 192.168.0.1: icmp_seq=1 ttl=64 time=1.19 ms 64 bytes from 192.168.0.1: icmp_seq=2 ttl=64 time=0.417 ms 64 bytes from 192.168.0.1: icmp_seq=3 ttl=64 time=0.382 ms
In this example we have a latency of below 1 milisecond and 192.168.0.1 is up
Broadcast ping
A broadcast ping can be described as a request "Anybody who hears this, please respond back". The problem is that you can configure computers to ignore these requests.
To tell your computer to answer on broadcast pings, open a console and issue:
echo "0" >/proc/sys/net/ipv4/icmp_echo_ignore_broadcasts
To verify if your computer is set to answer on broadcast pings, issue:
sysctl net.ipv4.icmp_echo_ignore_broadcasts
In this case, the response
net.ipv4.icmp_echo_ignore_broadcasts = 0
means it is set to answer.
To perform a broadcast ping,
- Find out the broadcast address of the network where you want to broadcast
ifconfig eth1
eth1 Link encap:Ethernet HWaddr 00:1C:F0:BB:06:C8
inet addr:192.168.0.5 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::21c:f0ff:febb:6c8/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:315742 errors:0 dropped:0 overruns:0 frame:0
TX packets:297176 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:195071533 (186.0 Mb) TX bytes:41401952 (39.4 Mb)
Interrupt:21 Base address:0x4000
- ping the broadcast IP
# ping -b 192.168.0.255 WARNING: pinging broadcast address PING 192.168.0.255 (192.168.0.255) 56(84) bytes of data. 64 bytes from 192.168.0.5: icmp_seq=1 ttl=64 time=0.039 ms
Broadcast ping does not work?
try nmap like this:
nmap 192.168.0.0/24
Ping does not work
If you change a host's IP in /etc/hosts and this change is not reflected instantly by ping, restart the name service cache daemon:
/etc/init.d/nscd restart
and check /etc/nsswitch.conf
